Cisco CUCM इंटीग्रेशन

फीचर्स

SIP trunk or CUBE SBC integration
IP-based or credential-based authentication
Enterprise-grade DID routing
Supports TLS/SRTP for secure signaling
Route patterns and translation patterns for DID mapping

कैसे कनेक्ट करें

Create a SIP trunk in CUCM

In CUCM Administration, navigate to Device > Trunk. Create a new SIP Trunk pointing to sip.cliqtel.com.

Configure SIP trunk security profile

Set up a SIP Trunk Security Profile with the appropriate transport (UDP/TLS) and authentication settings.

Create route patterns

Add route patterns to direct inbound calls from Cliqtel DIDs to the correct directory numbers and partitions.

Test and validate

Use CUCM RTMT to verify trunk registration. Make test calls for inbound and outbound routing.

आवश्यकताएँ

Cisco CUCM 12.x or later
CUBE gateway or direct SIP trunk capability
Admin access to CUCM administration
Network reachability to sip.cliqtel.com
At least one Cliqtel number

Trunk कॉन्फ़िगरेशन

जब आप कनेक्ट करते हैं, तो इन ऑप्टिमाइज़्ड डिफ़ॉल्ट के साथ एक SIP trunk बनाया जाता है:

transport

udp

codec preference

g722,ulaw,alaw

nat mode

off

auth type

credentials

max channels

10

पोस्ट-सेटअप चेकलिस्ट

SIP trunk shows active in CUCM RTMT
Inbound call reaches the correct directory number
Outbound call routes through Cliqtel trunk
No certificate errors (if using TLS)

Cisco CUCM + Cliqtel: उपयोग के मामले

Replace your current SIP provider

Migrate your Cisco CUCM system from an expensive SIP provider to Cliqtel without changing your PBX configuration — same SIP protocol, transparent per-number pricing.

Add international numbers to Cisco CUCM

Expand your Cisco CUCM deployment with local, toll-free, and mobile numbers in 70+ countries. Assign them to extensions or queues exactly as you do today.

Failover and redundancy

Add Cliqtel as a secondary SIP trunk for Cisco CUCM to fail over when your primary carrier has an outage. Keep your customers reachable 24/7.

Cisco CUCM इंटीग्रेशन — FAQ

How do I connect Cliqtel to Cisco CUCM?

Create a SIP trunk in your Cliqtel portal, copy the credentials, and paste them into Cisco CUCM's SIP provider settings. A full step-by-step guide is in the setup steps above.

Does Cliqtel work with my version of Cisco CUCM?

Cliqtel supports all current and recent versions of Cisco CUCM. Check the supported versions list above or contact support if you're running an older release.

How much does it cost to use Cliqtel with Cisco CUCM?

Cliqtel has no setup fees, no monthly platform fees, and no channel limits. You pay only for the DID numbers you rent (from EUR 1.49/mo) and the minutes you use. See our pricing page for details.

Can I use my existing phone numbers?

Yes. Cliqtel supports porting for most countries. Contact support with your existing numbers and we'll check portability and timelines (typically 5-10 business days).

Does Cisco CUCM need any special firewall configuration?

Open UDP 5060 (SIP) and UDP 10000-20000 (RTP) outbound to sip.cliqtel.com. Most PBX systems handle this automatically if you're not behind a strict NAT.

क्या आप Cisco CUCM कनेक्ट करने के लिए तैयार हैं?

सेकंडों में एक प्री-कॉन्फ़िगर्ड SIP trunk बनाएं। आपके क्रेडेंशियल्स तुरंत जनरेट होते हैं।

Cisco CUCM